Tamko Gutter Replacement in Dallas, TX

Tamko Gutter Replacement: The Dallas Owner’s Guide

Tamko gutter replacement in Dallas typically runs $280-$520 for a standard residential section including removal, new matching Tamko-compatible components, and proper sealing. Most jobs we handle same day or next morning, and we stock the common profiles on our trucks. Homeowners usually notice the problem first as water spilling over the front edge during a hard Texas downpour, or they spot a sagging section pulling away from the fascia after years of thermal expansion.

Call (888) 309-8379

Which Tamko Models This Applies To

Tamko’s gutter line breaks into two main families: the Heritage series (5-inch K-style, .032 aluminum) and the Titan series (6-inch K-style, .027 aluminum with a slightly wider bottom). The Heritage is what you’ll find on most Dallas homes built between 1995 and 2015; the Titan came in later for larger roof planes. Check the back of your gutter for a stamped Tamko logo and a date code, or measure the face width with a tape measure. The K-style has that decorative ogee curve on the front; if yours is flat-faced, it’s a different manufacturer entirely.

We carry OEM Tamko replacement sections and hangers, plus a heavier-gauge aftermarket equivalent from Spectra Metals that matches the profile exactly but uses .040 aluminum. For Dallas, we often recommend the aftermarket on south- and west-facing exposures where the metal sees 180-plus days of direct sun and thermal cycling is brutal. The OEM is fine for shaded or northern exposures. Clint Harwell made the call years ago to stock both after watching too many homeowners pay for a second replacement when the original gauge couldn’t handle the heat.

Signs Your Tamko Gutter Replacement Is Failing

• Water pours over the front edge during moderate rain. This usually means the gutter has pulled out of level, either from hanger failure or fascia rot behind the gutter. The low spot fills before the downspout can drain it.
• Visible sag between hangers, or the gutter tilts forward. Tamko’s standard hidden hanger spacing is 24 inches on center; in Dallas, the expansion from summer heat can pop screws from soft pine fascia, creating a belly in the run.
• Seams leaking at corners or end caps. Factory sealant on older Tamko units degrades after 8-12 years in Texas UV. The water runs behind the gutter and stains the fascia board.
• Downspout pulling away from the gutter outlet. The outlet tube is crimped into the gutter bottom; if the crimp loosens, the weight of a full downspout separates the joint.
• Paint chalking or white oxidation on the gutter face. This is cosmetic but signals the aluminum’s protective coating is spent. Once the finish fails, the metal thins faster, especially where standing water collects.

Replacement Cost & What’s Included

What drives the range: fascia condition (we replace rotted wood at $45-$75 per linear foot), single-story versus two-story access, and whether your Tamko system uses the older spike-and-ferrule fastening or the newer hidden hanger system. Our estimate includes removal, disposal, new hangers spaced 18 inches on center (tighter than factory spec for Dallas wind loads), sealant, and alignment to proper slope. Every gutter job carries our 90-Day Done Right Promise - if it doesn’t drain right, we come back. No paperwork, no arguing.

DIY or Call Us?

Here’s what you can safely check yourself: confirm the gutter is actually level with a 4-foot spirit level, clear debris from the downspout with a garden hose, and look for obvious hanger separation. What you should not attempt: working from a ladder on uneven Dallas soil (our crews use stabilizers and standoff brackets), cutting aluminum with anything less than a dedicated miter saw with a fine-tooth blade, or trying to reseal a corner from below. The sealant needs a clean, dry surface and proper clamping time - something you can’t get on a ladder in August heat.

We’ve also seen homeowners buy the wrong profile, install it with the slope reversed (water runs away from the downspout), or fasten into rotted fascia that fails six months later. A roof doesn’t lie - and neither do we. If you’re not certain what’s behind that gutter, call us. We’ll photo-document what we find and give you a number that doesn’t change.

FAQs